laser machine manual

Filter replacement......................................................................... 43
Daily cleaning and protection of the machine............................................... 43
Daily maintenance and cleaning of the handle............................................... 43

Chapter 1 Introduction

Respected user:

Welcome to use semiconductor laser hair removal machine, our semiconductor laser hair removal machine can get your trust, we are deeply honored. In order to give you a general understanding of our company’s products and make it easier for you to use, we have specially configured an instruction manual for you, which contains the characteristics of the machine, technical characteristics, screen machine operation functions, installation instructions, instructions for use, and instructions for daily maintenance , Troubleshooting, etc., is an indispensable guide when you use this machine. Please read the instruction manual carefully before use, I believe it will be very helpful for you to use this machine effectively. In addition, if you have any questions during use, please consult online, and we will serve you wholeheartedly. Special statement:

In order for you to use the treatment machine safely and effectively, read the instructions carefully before using it. Taboo:

Cancer; especially skin cancer
Pregnancy (including IVF)
Using photosensitive drugs and herbal medicines, laser irradiation is contraindicated
 Diseases that may be stimulated by laser irradiation
 Prolonged exposure to sunlight or artificial tanning before treatment and within 3 to 4 weeks after treatment
 Active infection of herpes simplex in the treatment area
 History of keloid scars
 Fragile and dry skin
 Hormonal disorders (under strong light stimulation)
 Use of anticoagulant
 Epilepsy
 History of coagulopathy

Chapter 2 Security

2.1 Electrical safety

1、When the power source is overloaded, the air switch at the back of the machine will trip to protect the machine. After the power supply is normal, close the air switch and restart the machine.

2、Software protection, the machine monitors the water flow in real time when the machine is running. If the water flow does not circulate, the machine will beep to remind the operator to protect the machine and the operator.

2.2 Laser safety

1、The handle must not be aimed at the eyes to prevent laser burns.

2、Yellow indicator light and buzzer located on the machine.

When the machine is ready to trigger the pulse, the yellow indicator light flashes, and when the pulse is triggered, the indicator light is always on.

When the machine triggers the pulse, the buzzer will beep.

The laser can only be triggered when the operator switches to the Ready mode.

3、When the machine is running, water circulates through the handle to cool the laser.

The machine monitors the water flow and temperature to eliminate the risk of overheating the handle. If the water flow stops or the water temperature is higher than 40°C, the machine will alarm.

Laser hazard signs (see Figure 2-1, Figure 2-2) are located on the left and right panels of the machine.

The emergency stop knob logo is located on the left side of the emergency stop knob 2-3 ，Figure 2-

2.1 General Cautions

1、Cautions

The operator should thoroughly read this manual before attempting to operate the machine.

The treatment head of the handle must be kept clean at all times. Wipe the treatment head clean after each use. Keep the handle dry.

The machine weighs about 110 lbs (50 kg). If you do not pay attention to protection when moving, it may cause injury. The machine is designed with a handle. Push the handle of the machine and move it slowly and carefully. Do not pull the machine by the handle or cable.

Cautions

Only personnel authorized by the manufacturer can repair and disassemble the machine. This includes internal disassembly and repair of machines, handles, etc.Confirm that the machine is used for your country's standard voltage (120VAC or 230VAC).Only when the machine is turned off and disconnected from the power supply, the operator can perform maintenance, otherwise it may cause injury to the operator or damage to the machine.Do not leave the machine while it is running.Never allow untrained personnel to operate the machine.Before treating the customer, check the handle for damage. If there is any obvious damage, do not use the handle.During machine maintenance, do not leave the machine or leave the machine when it is running.

3、Danger of burning

The semiconductor laser hair removal machine emits a high-intensity laser, which is invisible to the human eye and can cause burns.

Both direct and reflected light are dangerous to the eyes.During the treatment, all people present must wear the protective glasses provided by us to protect their eyes.Instruct customers to close their eyes even if they wear protective glasses during treatment.If the customer cannot wear protective glasses, please equip the customer with an opaque eye protection cover and completely cover the eyes. If the treatment area is very close to the eyes (such as the eyelids), protect the eye

Safety glasses

All persons must use safety glasses, and make sure the glasses provide enough protection: (doctor glasses image 2-5, customer glasses image 2-6)

The machine include a doctor glasses, a customer glasses, and more can be ordered separately.

Explosion and fire hazards

The laser may ignite the flammable and explosive materials, so preventive measures must be taken. There should be no flammable and explosive materials around the machine.The machine is not suitable for use in the environment with flammable mixture.Do not operate the machine around alcohol, gasoline or other volatile

solvents.During treatment, do not use alcohol or acetone and other flammable substances for treatment. If necessary, wash the treatment area with soap and water before treatment.If using alcohol to clean and

disinfect the handle treatment head, please dry the handle thoroughly after disinfection.Flammable and explosive materials must keep a safe distance from the machine

Danger of high pressure

The machine uses 120 / 230VAC. To avoid personal injury, do not operate the machine until the power cord and handle are properly installed. Don’t attempt to disassemble the machine or handle.The machine will have a high current output during treatment, and some parts may retain charge after the power is turned off. So any part of the external shell (except the plug cover) should not be removed, unless A professional equipment person.During the machine is maintained , Don’t leave the machine while it’s in operation.

Start the machine

The power cord connecting the machine must be grounded.The machine is equipped with many safety functions. All treatment persons should be familiar with the saft position and operation.Power line connection position, air switch (image 2-7

8、Emergency button ， Figure 2-8

This red button is used for emergency stop.When pressed, it immediately turns off the power of the entire machine

To release the emergency stop button, turn clockwise . Otherwise, the machine will remain off.

9、Cooling system

The treatment head is water-cooled during work to reduce the pain of the patient during treatment and reduce postoperative side effects such as local skin redness and swelling. The handle cools the skin through the metal cap on the front of the handle. The temperature of the treatment head will drop to 0℃~-5℃ during the treatment by the machine. Handle treatment head (Figure2-9)

2.4 Device label

Chapter 3 Installation

3.1 Introduction

The machine is designed for installation in an office or clinic. When you receive the machine and complete the on-site installation, start to test and use our machine.

The transportation and installation of the machine are carried out by the users who will do the following tasks:

a) Unpack the machine and position it in its pre-selected position (installation position).
b) Verify the integrity of the machine and its components, (equipment list).
c) Connect the machine (handle, machine, foot switch, power cord).
d) Plug the power cord of the machine into a designated power outlet.
e) Add deionized water or purified water to the water tank.
f) Test the machine to check whether the water flow is normal (normal value 4.0-5.0L/min) and whether the machine has alarmed.

Finally, if necessary, coordinate on-site safety inspections.

3.2 Equipment list

The main body and handle of the machine, Figure 3-1

2、Machines’ Accessories

3.3Facilities requirements

1、Space and positioning

The machine should be installed in a well-ventilated location. The working area of the machine should be prepared according to the machine size shown in (Figure 3-3). To ensure proper ventilation, keep both sides of the machine at least 20 inches (0.5 meters) away from walls or other obstacles that impede air flow. After positioning the machine, lock the front casters to secure the machine by pressing the pedals on the top of the two casters at the front of the machine.

2、Electrical requirements

The machine is pre-assembled by us and customized by the customer, so the customer needs a separate power socket after receiving the machine：

120VAC±10%，50/60Hz，or：

230VAC±10%，50/60Hz，

There should be no momentary changes or surges in the input power supply. Therefore, the machine power cord should not be shared with other heavy variable loads such as elevators, air conditioning systems, and large motors.

The power socket used by the machine must be grounded. A good grounding is essential for safe operation.

3、Environmental requirements

Air quality：

The machine should be operated in a non-corrosive environment. Corrosive gases can damage wires, electronic components, and optical components.

Dust particles in the air should be kept to a minimum. Dust particles absorb light and heat up, and their entry into the crystal will affect the treatment effect, and severely burn the laser. Metal dust is destructive to electrical equipment.

Water quality: The machine should use deionized water or purified water. Regular tap water contains deposits that damage the cooling system and lasers.

Temperature: To ensure the best performance of the machine, keep the room temperature between 24°C and 26°C

3.4Turn on the machine

1、Open the package and check the equipment, equipment placement: open the package after receiving the machine (Figure 3-4)

As shown in the Figure above: Step 1: Straighten part 1 with pliers; Step 2: Turn the second part counterclockwise to unlock it

Open the packing box, take out the foam, take out the accessories and check the accessories, (Figure 3-5), see 3.2 Equipment List for details

Two people work together to lift out the machine: Figure 3-5.1: The position where it cannot be carried (handle, plastic shell),
Take out the machine and slowly place it on a flat ground.

3.5Install the machine

The connection between the handle and the machine, and the lock connector socket on the machine (Figure 3-6). It is designed to facilitate the replacement of the handle.

Insert the handle connector into the lock connector socket (located under the cover (Figure 3-7), and align the guide pin (Figure 3-8) on the handle lock connector plug head (Figure 3-8) with the lock connector plug The guide hole of the pull seat (Figure 3-6).

Turn the knob of the lock connector (Figure 3-9) clockwise one turn, the handle can be connected to the machine. Handle placement is shown in figure (3-10)

Machine installation video tutorial

To remove the handle, turn the connector knob one turn in the opposite direction, and the connector will withdraw.

2、Power cord connection (see Figure 3-1

3、Foot switch connection (if necessary, optional installation) (see Figure 3-12)

Water injection (see Figure 3-12)

The water added in the water tank of the machine must be deionized or purified water. The water level in the water tank must be checked every three months. Refer to the water level line (Figure 3-13). Change the water once a month

Turn on the machine (need to check the position of the emergency stop knob, the key and the air switch on the back) (see Figure 3-14) (see Figure 3-15)

6.Observe the water level. When the water level is not reached, shut down the machine and add water to the water level indicator (see Figure 3-16).

7.The machine runs normally, the water flow is normal (see Figure 3-17), and the handle head is normal for refrigeration and frosting (15min) (Figure 3-18)

Congratulations on the normal operation of the machine, ready to serve you.

3.6 Moving the machine

To move the machine, please do the following:

Place the handle on the handle holder (Figure 3-18).

Disconnect the power cable

Release the caster brake.

Slowly push the handle to move the machine.

Chapter 4 System Introduction

4.1 General system description and intended use

808 laser hair removal is based on the principle of photothermal dynamics, because the human skin is a relatively light-transmitting structure. In front of a powerful laser, the skin is like a transparent glass, and the laser can penetrate the skin to the hair follicle very smoothly. It is the part where the hair grows, and the melanin in the hair follicle absorbs a large amount of laser energy and finally converts it into heat energy to increase the temperature of the hair follicle, thereby destroying the function of the hair follicle, making the hair lose the ability to regenerate, and then achieving the purpose of hair removal.The whole machine is composed of a host, a handle and a foot switch. When the operator uses the handle to treat the customer, he presses the button on the handle or steps on the foot switch and the machine emits pulsed light.

4.2 Machine components and controls

The machine contains the following components:control Panel\Power module\cooling system

4.3 System control

Emergency shutdown knob (Figure 4-1) This is a red, mushroom-shaped knob for emergency shutdown of the machine.

Three power modules provide power to the components of the system:

32V100A power supply-to-light/laser current driver

150W/24V-to provide power to the water pump and the thermoelectric tissue cooling system

350W/12V-Provide power to touch control screen and microcontroller board

4.5system software

The machine system adopts embedded software. The operator can directly control the operating parameters of the system through the touch control screen and run routine tests to ensure normal operation. Error detection.

4.6cooling system

The cooling system includes:

Water cooling system: The water cooling system is implemented in a closed loop system that uses deionized water or purified water to ensure the long life of the laser. The cooling system includes a radiator, a water tank, a water pump, and a water filter. The machine also includes a temperature sensor and a turbine flow meter. The water temperature and water flow speed of the machine are displayed when the machine is running.

4.7 Handle

Handle: The laser in the handle uses American and German (imported) chips (lasers).

4.8Power requirements

Choose according to local power requirements or contact us to confirm the accuracy before use

Chapter 5 Operating System

5.1Screen operation guide

1、Boot interface (the initial welcome interface is shown in Figure 5-1)

Click anywhere in the initial welcome interface to enter the function selection interface (Figure 5-2)

:Click the function selection button, the system will jump to the male and female selection menu interface (Figure 5-3)

Click the system setting button, and the system will first jump to the password input interface. After entering the correct password, it will jump to the system setting interface (Figure 5-4)

The system setting interface has the following functions:

: Display area for the number of times the handle shines

:Password change key。

: System parameter reset button. Click this button, the system will reset all processing parameters and reload the program from the initial interface.

:Water flow detection button. Click this button to turn on or off the water flow detection function.

：Turn on water flow detection.

:Turn off the water flow detection function.

:Click Back to return to the function selection interface.

1.Choose gender

：When the user is a female, click the female selection button (HR) to read the preset parameters of female treatment

：When the user is male, click the male selection button (SR) to read the preset parameters of female processing

：Click Back to return to the function selection interface

4、Select the part (see Figure 5-5) (Figure 5-6)

：When the user processes the face, click the "face" button according to the user's gender, and jump to the treatment parameter work interface (Figure 5-7), (Figure 5-8)

：When the user is processing the armpit, click the armpit button according to the user's gender to jump to the working interface of treatment parameters

：When the user is treating the chest and abdomen, click the chest and abdomen button according to the user's gender to jump to the working interface of the treatment parameters

When the user handles the arm, click the "arm" button according to the user's gender to jump to the treatment parameter work interface

When the user processes the legs, click the "legs" button according to the user's gender to jump to the treatment parameter work interface

： Click Back to return to the male and female selection menu interface (Figure 5-3)

Select treatment parameters: the working interface of treatment parameters (Figure 5-7) (Figure 5-8)

Processing parameters and working interface have the following functions

：Display the spot size of the selection handle.

：Counting information display box. The upper box shows the current count in progress. When exiting this interface, the current count will be automatically cleared; the count can display up to 8 digits.

: In the skin color selection area, select a similar skin color type according to the user's skin color.

：Energy display and adjustment function box. This box displays the energy level currently set. Press the up and down keys to adjust the energy level, and press the up and down keys to continuously adjust. The minimum value of energy adjustment is 1j/cm2, and the maximum value of energy adjustment is 150j/cm2. The plus and minus key only responds in the non-working state, and does not perform any operation during the working process.

：Pulse width display and adjustment frame, plus and minus keys for continuous adjustment. The minimum value of time adjustment is 10ms, and the maximum value of time adjustment is related to frequency and energy. This plus and minus key only responds in the non-working state, and does not perform any operation during work.

：Frequency display adjustment function box, display the currently set frequency size, plus and minus keys to adjust the frequency size, plus and minus keys for continuous adjustment, the adjustable frequency range is 1~10HZ, within the range of 1~10HZ, the adjustment step is 1HZ, adjust At frequency, the time value changes with the change of the frequency value. The change value is the preset value. This plus and minus key only responds in the standby mode, and does not perform any operation during the preparation process.

：The water flow value display box displays the water flow value, accurate to one decimal place. When the water flow rate is less than 1.6l/min, it means that the water flow rate is small, and the system will forcefully jump to the standby state. This item will turn red and the system will sound an alarm.

：Click the ready button to enter the ready state, the system will send a power-on command to the laser power supply, and the handle will automatically begin to cool down.

：Standby button, the system sends a power-off command to the laser power supply, the device enters the standby state, and the handle stops cooling.

：Cooling control button. This button is only available when the system is in the ready state. If the system is in the ready state by default, click to turn off the refrigeration, and then click to turn on the refrigeration again. If the system is in the standby state, the refrigeration is off, and this button is invalid. Three snowflakes represent three cooling levels

：The temperature display area shows the air temperature and the water temperature in the water tank. When the air temperature and the water temperature in the water tank are greater than 40°C, the temperature is too high and the system will switch to standby mode. This item will turn red and the system will sound an alarm.

：The handle shines on the display area. When the machine emits laser light, this lightning bolt symbol will turn red, otherwise it will be white.

：Click the "Back" button, and the system will jump to the welcome interface. (Figure 5-1)

：Click Back to return to the location selection interface (Figure 5-5, Figure 5-6)

：：Click the language selection button, and the system will jump to the language selection interface (Figure 5-9)

：Click the system setting button, and the system will first jump to the password input interface (Figure 5-10). After entering the correct password, it will jump to the system setting interface, as shown in (Figure 5-4).

：When the Ready button is not clicked, the volume of the control button is adjustable (level 0-3), and when the Ready button is clicked, the volume of the control light is adjustable (level 0-3)

0 means no sound; 3 means the highest level

Language selection interface

: English selection button. Click on the production screen language English to jump to the function selection interface (Figure 5-2)

：Russian selection key. Click to make the screen language Russian, and then jump to the function selection interface (Figure 5-2)

：German selection key. Click on the production screen language German to jump to the function selection interface (Figure 5-2)

：Swiss language selection key. Click to change the screen language to Swiss, and then jump to the function selection interface (Figure 5-2)

：Spanish selection key. Click to change the screen language to Spanish, and then jump to the function selection interface (Figure 5-2)

：Turkish language selection button. Click on the production display language Turkish to jump to the function selection interface (Figure 5-2)

The password input interface has the following functions:

：Numbers are 0~9: number input button, the password displays 6 digits, no more changes than 6 digits.

：Delete button, press this button to delete the last input number.

：Password confirmation button. Press this button. If the password is entered correctly, enter the corresponding password according to the previously clicked function, and the corresponding interface will jump. If the password is wrong, if the password is wrong, the password is cleared and needs to be entered again.

Chapter 6 Guidelines for Treatment Parameters

6.1 For the setting of treatment parameters, please refer to the analysis of “treatment parameters”.

Chapter 7 Treatment Steps

Warning:

If the patient feels intense pain, please stop treatment. In case of burns, use scald cream immediately.

1、Wipe clean the treatment area(Figure7-1) 2 Shave hair to 1-2mm（Figure7-2）

3 Apply the cooling gel evenly to the treatment area.

4、Set the parameters according to the skin color (Figure 7-3) (for detailed skin selection, see Chapter 5 for the parameter selection button)

The treatment head should be close to the skin, and slide the treatment for at least 5-10 times

Sliding longitudinally at least 5-10 times

Oblique sliding at least 5-10 times

In this way, energy can be introduced into the hair follicle from all angles.

Note: don’t slide too fast

For detailed operation steps, please refer to the treatment video tutorial:

After the treatment, clean the treatment area and wipe off the gel with a paper towel.(Figure 7-4)

Chapter 8 Troubleshooting

8.1 Water flow alarm

Cause Analysis

1)Is the handle inserted all the way；

2)Whether the one above the water tank cover is open;

3) The filter has not been replaced for a long time.

8.2 Abnormal water temperature

Abnormal water temperature is generally caused by damage to the temperature probe. For detailed troubleshooting and maintenance, please refer to the after-sales maintenance manual

Maintenance Manual V3.0.docx

9.1 Filter replacement

Chapter 9 Daily Maintenance

1、The filter with resin does not need to be replaced(Figure 9-1）

2、The filter without resin is replaced every 6 months according to the usag（Figure 9-2）

Filter replacement video tutorial：https://cloud.video.alibaba.com/play/u/2153292369/p/1/e/6/t/1/d/hd/301728204487.mp4

9.1 Daily cleaning and protection of the machine

Ensure that the machine is clean during daily use, and protect it when not in use to prevent dust from falling into it and avoid damage due to impact.

9.2 Daily maintenance and cleaning of the handle

After use, the handle should be disinfected and wiped clean in time to keep the handle dry and clean.

Emial ..............................................................................

Tel.....................................................................................

Website.............................................................................

808-V19 Instruction Manual

Configuration: 808-V19, 4K screen diode laser machine

Authorized representative of the European Community and patents：

Catalogue